Xante aw 1200 manual

Page 57 Configure the Printer Setup on the Network Page 59 Installing the Optional Cassette Page 61 Clearing a Cassette Area Jam Page 62 — Troubleshooting LED 1 Red Fig. Either the top or front printer cover is open or no toner cartridge is installed. Make sure a cartridge is installed and the front and top covers are closed securely.

Page 68 The printed image is faded. Reduce the size of the media stack. Recurring stains appear on output. Media may not meet printer requirements in chapter 6. Media wrinkles. Page Media Jams Turn off the printer and wait a few seconds. If media wraps around the heat roller or you see smoke coming from the printer, immediately turn off the printer and disconnect the power source. Then, slide the cassette back into the printer until it snaps into place fig. Page 76 Fig. For position D: Hold the ends of the jammed media and pull it slowly up and out through the output tray.

Page Checklist For Frequent Jams Are the cassette side and end guides adjusted to the correct position for the loaded media? Media Feeding Issues If media fails to feed into the printer from a cassette, use the following procedure. Page Removing Cables And Media If you have a toner vacuum, use it to remove all loose toner in the printer before shipping it.

Removing Cables and Media Turn off the printer and disconnect the power cord from the printer and power source.

Then, disconnect all attached interface cables. Page Removing The Optional Feeder Always lift the printer from the bottom recessed grip areas on each side not from cassette openings and keep it level within 5. You will need a roll of heavy-duty packing tape. Page 82 Fig. Always lift the printer from the bottom recessed grip areas on each side not from cassette openings and keep it level within 5. Page Technical Support If you are doing a full return, the documentation and software fit in the output tray on top of the printer.

The power cord fits inside the bottom shipping stabilizer, and the toner cartridge goes behind the printer. Cushion these items with crumpled paper to hold them in place during shipment. Page 84 bold faced on the questionnaire fig. From this site, you can download printer drivers, software, PPDs, and access other technical information. Page 85 — Maintenance, Specifications, and Warranty The printer weighs approximately 27 lbs 12 kg without toner, cassettes, and media installed.

Always lift the printer, using the recessed grip areas on the right and left sides only. Turn off the printer and unplug the power cord from the printer and power source.

Page Storing The Printer Store the printer and media properly. Store the printer and media in their original packaging or cover them to protect from dust. Page 88 Remove any paper scraps and wipe off paper and toner dust with a clean, dry, lint-free cloth fig. Never use alcohol, ammonia-based cleaners, or other volatile cleaners on or around the printer. Never spray or pour water directly on the printer. Always dampen a clean, lint-free cloth with water and wipe the printer with that cloth.

Page Printer Memory Requirements Memory requirements depend on file and media size. Complex, large, or heavy graphics files may require more than standard memory to print. In many cases, this prevents the need for a site visit and limits downtime. Page 94 — Printing on Various Media and Options Page Media Specifications Media Specifications To ensure that your job prints correctly, use appropriate media.

Store and handle it carefully to prevent damage to the media or printer. This section covers selecting Media and describes media types and sizes for use with your printer.

Page Imageable Area Physical page size differs from the imageable area. The imageable area is the physical page area on which the printer can lay down toner.

The following chart lists physical page sizes for standard media your printer handles. Page Printing On Custom Sized Media If you want to print a custom size, make sure the dial is set to Others; then any page size can be used. If a media size that is different from the dial setting is loaded in the printer, a document will not print until the dial is reset to the correct size.

Page Media Handling The paper is delivered into the output tray. Media Sources Your printer has two built-in paper cassette feeders. The top feeder holds the sheet multipurpose cassette; the second feeder holds the standard sheet cassette.

These two cassettes provide an input capacity of approximately sheets of 17 lb bond 64 to Page Optional Paper Feeder Optional Paper Feeder You can add an optional paper cassette feeder to your printer to increase input for standard paper to approximately sheets.

Page Tray Chaining Use the following guidelines for tray chaining. If the printer detects a different size media when it switches to the new tray, the printer stops printing. When tray chaining is enabled, an incorrectly positioned tray will prevent the printer from printing. Page Printing Envelopes Printing Double-Sided Copy You can print double-sided copy manually by feeding paper through the printer twice.

Print the first side of the paper. Remove the paper from the output tray, straighten any curling edges, and allow it to cool thoroughly. The weight of a large stack could cause the sheets to stick together. If you use these types of cards, lightly wipe the powder off both sides of the card using a dry lint-free cloth. Page Installing The Optional Paper Feeder Installing the Optional Paper Feeder An optional feeder and paper cassette can be added to your printer to increase input capacity for standard paper to approximately sheets.

Turn off the printer, unplug the power cord from the printer and power source, disconnect all interface cables, and remove any media output tray. Page Controller Board Upgrades Install the upgrade s. Reassemble the printer. Always use an antistatic procedure when working with the controller board.

Use an anti-static wristband or touch an unpainted metal surface to eliminate static electricity before handling a circuit board. Turn off the printer, disconnect the power cord from the power supply, disconnect any interface cable, and remove any media in the output tray. Page Use a magnetized screwdriver to remove the metal screws.

This could cause damage to the printer which is not covered by the warranty. Page fig. Then, set the board on a clean surface next to the printer. Page Screw the four stand-off posts into the four corner holes on the bottom of the IDE hard disk fig. Page Reinstall the controller board into the printer.

Grasp the controller board by the front, right corner and the left memory bank latch and align the board over the printer at a slight angle fig. Page Replace the 4 screws to secure the controller board to the printer fig. You can upgrade printer memory to MB or to MB. If you order a memory upgrade with your printer it will be installed before the printer ships.

Page Fig. This activates the RAM upgrade memory bank. Open the end latches on the RAM memory bank by rotating them out and down fig. Page Reassembling The Printer After you install a controller board upgrade, use the following procedure to reassemble the printer. Align and lower the controller cover onto the printer fig. Page Tighten the three controller cover screws fig.

Page — Printing on Various Media and Options Page PostScript Files The optional feeder and tray upgrade is used as an example for this procedure. The Chooser Window appears fig. Then, select File: Properties. The Properties window appears fig. This section covers going to the home page and accessing printer features, options, and information available there.

Go to the printer home page fig. Page The Information Pages window allows you enable or disable printing of the start-up page or the low toner page. Select Printer Configuration: Informational Pages.

The Informational Pages window appears fig. Page To help ensure print quality, make sure the selected media type matches the media type loaded in the corresponding cassette. To select the media Go to the printer home page fig. Select Printer Configuration: Media Types. The Configure Media Types window appears fig.

The imageable area is the portion of a page on which the printer can lay down toner. The Reset Factory Defaults window appears fig. To access this information Go to the printer home page fig. Select Printer Information fig. Printer information options appear fig. Page General Information RAM size, engine speed, page count, and PostScript margin settings as well as whether the startup-page and low toner page printing is enabled on or disabled off. Select Printer Maintenance: Clean Printer.

The Clean Printer window appears fig. Use this program to load and manage font files in your printer and to send PostScript files to your printer. Using this menu, you can print a list or view on screen all fonts downloaded to printer ROM, memory, or an optional hard disk. Delete allows you to remove fonts that have been downloaded to memory or the optional hard disk.

The following window appears fig. Where would you like the directory sent? PS3 file or download the Fontsamp. Page Postscript Files Screen Shape The Screen Shape feature allows you to select the shape of dots that make up the screen pattern for your printed image. The following steps are required to set up your printer to communicate using the Line Printer interface on the Ethernet board. Chapter 1 covers step 1; this section covers steps 2 and 3.

Page Network Masks In the absence of subnetting, the broadcast address is created by using the network ID address octets and all 1s for the host ID octets. Page Using The Setip. If you do not get full replies, verify that you have the correct IP address configured for your printer. These steps assume you already have an NDPS manager defined.

Load NDPS. Page Printer Package Printer Package The printer weighs approximately 27 lbs 12 kg without toner, cassettes, and media installed. Always lift the printer from the bottom recessed areas on each side not from cassette openings and keep it level within 5. Unpack the printer saving the packing materials.

If you ordered the optional feeder and cassette s , they are packaged separately. Printer Overview Use Figures 1. Output Cover Tray Quality and reliability of refilled toner cartridges vary, and printer damage caused by these products is not covered by your printer warranty. Handling the Toner Cartridge Then, hold the top cover on the right and left sides, lift up, and pull back fig. We are world leaders in advanced power products.

DS4 resembles a compact SUV in its design with a coupe-like silhouette. Select Matte Film from the Media Type drop-down menu fig. Free download as PDF File. Multi-patented next-generation audio repair tools that offer both fast and high-quality processing.

If you're repairing or changing a distributor cap in your car, learn how to visually inspect the distributor cap with the help of an expert in this free auto repair video.

Watch and learn from our expert how to reset your iPod, with a basic demonstration in this free electronics video on using an iPod for beginners. Page Blank areas appear in my image or text. Also for, Platemaker 4, Accel-a-writer 4. Learn where your washer fluid reservoir is located when repairing your windshield washing system from a car repair expert in this free car maintenance video.

Each person picks their own location, outfit and photographs the same model to showcase how different each of their styles are. The 5 passenger Santa Fe is the ultimate family-adventure vehicle. Xante platemaker 3 paper jam alert when when printing polyester plate from manual feed even though no paper is stuck in. View and Download Xante CL30 user manual online. To save these settings made in this procedure as the defaults for all print jobs, select Save Custom Setting from the Print window drop-down menu fig.

Moreover, our key privileges include user-friendly categorization, online viewing and possibility to download any manual. You may find Ebook Pdf Mitsubishi Endeavor Service And Repair Manual document other than just manuals as we also make available many user guides, specifications documents, promotional details, setup documents and more.

I buy this model in year and i've shot thousands of pics, today october is in very good mechanical condition and working very clever.

This lens hood is in excellent condition showing less than normal signs of use. And the socket where the external power supply goes is bent and needs repair.

By continuing to use this site, you accept our use of cookies and other online technology to send you targeted advertisements, for social media, for data analytics and to better.